View T545Y337M010ATE035_6875947.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 1 one world. one kemet benefts ? e xtremely low esr ? h igh energy delivery capability ? - 55c to 85c operating temperature range ? p olymer cathode technology ? h igh frequency capacitance retention ? n on-ignition failure mode ? ca pacitance up to 1,500 f ? v oltage: 6.3 C 16 v ? 1 00% accelerated steady state aging ? 1 00% surge current tested ? 1 00% thermal shock ? v olumetric effciency, very high capacitance ? s elf-healing mechanism ? t aped and reeled per eia 481-1, eia standard case sizes applications typical applications include hold-up, data hardening or vaulting for enterprise and military ssds, and high end desktop modems. overview the kemet organic capacitor is a tantalum capacitor with a ta anode and ta 2 o 5 dielectric. a conductive organic polymer replaces the traditionally used mno 2 as the cathode plate of the capacitor. this results in very low esr and improved capacitance retention at high frequency. the polymer technology also exhibits a benign failure mode which eliminates the ignition failures that can occur in standard mno 2 tantalum types. ta polymers may be operated at voltages up to 90% of rated voltage for part types with rated voltages of 10 volts and up to 80% of rated voltage for part types > 10 volts with equivalent or better reliability than traditional mno 2 tantalum capacitors operated at 50% of rated voltage. the t545 series was developed to deliver the highest energy per cc of any tantalum surface mount device (smd). this capability makes this capacitor an excellent solution for designs requiring high energy at relatively low voltages, such as data hardening or data vaulting for solid state drives (ssd's). the t545 series high energy polymer tantalum surface mount capacitor captures the best features of multilayer ceramic capacitors (low esr and high frequency capacitance retention), aluminum electrolytics (higher capacitance and benign failure mode) and proven solid tantalum technology (volumetric effciency, surface mount capability and extremely long life). in addition, this series is subjected to 100% thermal shock and voltage aging to insure long term reliability. kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum environmental compliance rohs compliant (6/6) according to directive 2002/95/ec when ordered with 100% sn solder. www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 2 2 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum spice for a detailed analysis of specifc part numbers, please visit www.kemet.com for a free download of kemet's spice software. the kemet spice program is freeware intended to aid design engineers in analyzing the performance of these capacitors over frequency, temperature, ripple, and dc bias conditions. ordering information t 545 h 108 m 006 a t e055 capacitor class series case size capacitance code (pf) capacitance tolerance voltage failure rate/ design lead material esr t = tantalum high energy polymer tantalum h, w, y, x, v, d first two digits represent signifcant fgures. third digit specifes number of zeros. m = 20% 006 = 6.3 v 010 = 10 v 016 = 16 v a = n/a t = 100% tin (sn) esr in miliohms performance characteristics item performance characteristics operating temperature -55c to 85c rated capacitance range 47 f C 1,500 f @ 120 hz/25c capacitance tolerance m tolerance (20%) rated voltage range 6.3 C 16 v df (120 hz) refer to part number electrical specifcation table esr (100 khz) refer to part number electrical specifcation table leakage current 0.1 cv (a) at rated voltage after 5 minutes www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 3 3 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum qualifcation test condition characteristics endurance 85c @ rated voltage, 2,000 hours** c/c within -20/+10 of initial value df within initial limits dcl within 1.25 x initial limit esr within 2.0 x initial limit storage life 85c @ 0 volts, 2,000 hours** c/c within -20/+10 of initial value df within initial limits dcl within 1.25 x initial limit esr within 2.0 x initial limit humidity 60c, 90% rh, 500 hours c/c within -5%/+35% of initial value df within initial limits dcl within 5.0 x initial limit esr within 2.0 x initial limit temperature stability extreme temperature exposure at a succession of continuous steps at +25oc, -55oc, +25oc, +85oc, +105oc, +25o c +25c -55c +85c c/c i l* +/-20% +/-20% df il il 1.2 x il dcl il n/a 10 x il surge voltage 85c, 1.32 x rated voltage, 1,000 cycles c/c within -20/+10 of initial value df within initial limits dcl within initial limits esr within initial limits mechanical shock/vibration milCstdC202, method 213, condition i, 100 g peak milCstdC202, method 204, condition d, 10 hz to 2,000 hz, 20 g peak c/c within 10 of initial value df within initial limits dcl within initial limits *il = initial limit **minimum temperature test condition 85oc www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 4 4 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum electrical characteristics esr vs. frequency capacitance vs. frequency 0.001 0.01 0.1 1 10 100 1,000 10,000 100,000 1,000,000 10,000,000 100,000,000 impedance & esr (ohms) frequency (hz) t545x337m010/010 impedance t545x337m010/010 esr 100 1,000 10,000 100 1,000 10,000 100,000 1,000,000 capacitance (f) frequency (hz) capacitance t545x337m019ate025 0.001 0.01 0.1 1 10 100 1,000 10,000 100,000 1,000,000 10,000,000 100,000,000 impedance & esr frequency (hz) impedance t545x337m016ate025 esr t545x337m016ate025 www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 5 5 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum dimensions C millimeters 15 termination cutout at kemet?s option, either end case size component kemet eia l* w* h* f* 0.1 (0.004) s* 0.3 (0.012) b* 0.15 (ref) 0.006 x (ref) p (ref) r (ref) t (ref) a (min) g (ref) e (ref) d 7343C31 7.3 0.3 (0.287 0.012) 4.3 0.3 (0.169 0.012) 2.8 0.3 (0.110 0.012) 2.4 (0.094) 1.3 (0.051) 0.5 (.020) 0.10 0.10 (.004 .004) 0.9 (.035) 1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) h 7260C20 7.3 0.3 (0.287 0.012) 6.00.3 (0.236 0.012) 2.0 (0.078) maximum 4.1 (0.161) 1.3 (0.051) n/a 0.10 0.10 (.004 .004) 0.9 (.035) 1.0 (.039) 0.13 (.005) 3.3 (0.13) 3.5 (.138) 3.5 (.138) v 7343C20 7.3 0.3 (0.287 0.012) 4.3 0.3 (0.169 0.012) 2.0 (0.079) 2.4 (0.094) 1.3 (0.051) n/a 0.05 (.002) n/a n/a 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) w 7343C15 7.3 0.3 (0.287 0.012) 4.3 0.3 (0.169 0.012) 1.5 (0.059) 2.4 (0.094) 1.3 (0.051) n/a 0.05 (.002) n/a n/a 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) x 7343C43 7.3 0.3 (0.287 0.012) 4.3 0.3 (0.169 0.012) 4.0 0.3 (0.157 0.012) 2.4 (0.094) 1.3 (0.051) 0.5 (.020) 0.10 0.10 (.004 .004) 1.7 (.067) 1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) y 7343C40 7.3 0.3 (.287 .012) 4.3 0.3 (.169 .012) 4.0 (.157) 2.4 (.094) 1.3 (.051) 0.5 (.020) 0.10 0.10 (.004 .004) 1.7 (.067) 1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) notes: (ref) C dimensions provided for reference only. no dimensions are provided for b, p or r because low profle cases do not have a bevel or a notch. * milCcC55365/8 specifed dimensions table 1 C ratings & part number reference rated voltage rated capacitance case code/ case size kemet part number dc leakage df esr maximum allowable ripple current msl rated temperature energy (mj) v f kemet/eia (a) @ v r , 20c maximum/ 5 minutes % @ 20c 120 hz maximum (mw) @ 20c 100 khz maximum (mamps) 45c 100 khz refow temperature 260c (c) (?cva2) - (?cvd2) va = voltage applied vd = voltage drop 6.3 1000 h/7260-20 t545h108m006ate055 630.0 20 55 1850.0 4 85 11.57 6.3 1500 h/7260-20 t545h158m006ate035 945.0 20 35 2300.0 4 85 17.36 6.3 1500 h/7260-20 t545h158m006ate055 945.0 20 55 1850.0 4 85 17.36 6.3 470 w/7343-15 t545w477m006ate035 296.0 10 35 2300.0 4 85 5.44 6.3 470 w/7343-15 t545w477m006ate055 296.0 10 55 1800.0 4 85 5.44 6.3 470 y/7343-40 t545y477m006ate025 296.0 10 25 3100.0 3 85 5.44 6.3 470 x/7343-43 t545x477m006ate006 296.0 10 6 6700.0 3 85 5.44 10 100 w/7343-15 t545w107m010ate040 100.0 10 40 2100.0 4 85 3.60 10 330 y/7343-40 T545Y337M010ATE035 330.0 10 35 2600.0 3 85 11.88 10 330 x/7343-43 t545x337m010ate006 330.0 10 6 6700.0 3 85 11.88 16 47 w/7343-15 t545w476m016ate045 75.0 10 45 2000.0 3 85 3,64 16 220 x/7343-43 t545x227m016ate035 352.0 10 35 2700.0 3 85 17.03 16 330 x/7343-43 t545x337m016ate025 528.0 10 25 3300.0 3 85 25.55 16 100 v/7343-19 t545v107m016ate055 160.0 10 55 1850.0 3 85 7.74 16 100 d/7343-31 t545d107m016ate055 160.0 10 55 2050.0 3 85 7.74 v f kemet/eia (a) @ v r , 20c maximum/ 5 minutes % @ 20c 120 hz maximum (mw) @ 20c 100 khz maximum (mamps) 45c 100 khz refow temperature 260c (c) (?cva2) - (?cvd2) va = voltage applied vd = voltage drop rated voltage rated capacitance case code/ case size kemet part number dc leakage df esr maximum allowable ripple current msl rated temperature energy (mj) www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 6 6 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum derating guidelines voltage rating maximum recommended steady state voltage maximum recommended transient voltage (1 ms C 1 s) -55c to 85c 6.3 v v r 10 v 90% of v r v r 10 v < v r 16 v 80% of v r v r v r = rated voltage ripple current/ripple voltage permissible ac ripple voltage and current are related to equivalent series resistance (esr) and the power dissipation capabilities of the device. permissible ac ripple voltage which may be applied is limited by two criteria: 1 . the positive peak ac voltage plus the dc bias voltage, if any, must not exceed the dc voltage rating of the capacitor. 2 . the negative peak ac voltage in combination with bias voltage, if any, must not exceed the allowable limits specifed for reverse voltage. see the reverse voltage section for allowable limits. the maximum power dissipation by case size can be determined using the table at right. the maximum power dissipation rating stated in the table must be reduced with increasing environmental operating temperatures. refer to the table below for temperature compensation requirements. temperature compensation multipliers for maximum power dissipation 45c 45 c < t 85c 85c < t 125c 1.00 0.70 0.25 t= environmental temperature using the p max of the device, the maximum allowable rms ripple current or voltage may be determined. i(max) = p max/r e(max) = p max*r i = rms ripple current (amperes) e = rms ripple voltage (volts) p max = maximum power dissipation (watts) r = esr at specifed frequency (ohms) case code maximum power dissipation (p max) mwatts @ 45c with +30c rise kemet eia t520t/t525t/t540t/ t543t 3528C12 105 t520m/t543m 3528C15 120 t520a/t543a 3216C18 112 t520b/t525b/t540b/ t543b 3538C21 127 t520u/t543u 6032C15 135 t520l/t543l 3528C19 150 t520c/t543c 6032C28 165 t520w/t545w/t543w 7343C15 180 t520v/t521v/t522v/ t545v/t543v 7343C20 187 t520d/t521d/t525d/ t540d/t545d/t543d 7343C31 225 t520y/t522y/t525y/ t543y 7343C40 241 t520x/t521x/t545x/ t543x 7343C43 247 t545e 7260C38 345 t520h/t545h/t543h 7260C20 187 t528i 3216C10 95 t528k 3528C10 150 t528w 7343C15 325 t528z 7343C17 325 t530/t541d 7343C31 255 t530/t541y 7343C40 263 t530/t541x 7443C43 270 the maximum power dissipation rating must be reduced with increasing environmental operating temperatures. refer to the temperature compensation multiplier table for details. www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 7 7 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum reverse voltage polymer tantalum capacitors are polar devices and may be permanently damaged or destroyed if connected in the wrong polarity. these devices will withstand a small degree of transient voltage reversal for short periods as shown in the below table. temperature permissible transient reverse voltage 25c 15% of rated voltage 55c 10% of rated voltage 85c 5% of rated voltage 105c 3% of rated voltage 125c* 1% of rated voltage *for series rated to 125c table 2 C land dimensions/courtyard kemet metric size code density level a: maximum (most) land protrusion (mm) density level b: median (nominal) land protrusion (mm) density level c: minimum (least) land protrusion (mm) case eia x y c v1 v2 x y c v1 v2 x y c v1 v2 a 3216C18 1.35 2.15 1.45 6.10 2.80 1.25 1.75 1.35 5.00 2.30 1.15 1.35 1.25 4.10 2.00 b 3258C19 2.35 2.15 1.45 6.10 4.00 2.25 1.75 1.35 5.00 3.50 2.15 1.35 1.25 4.10 3.20 c 6032C25 2.35 2.65 2.60 8.90 4.40 2.25 2.25 2.50 7.80 3.90 2.15 1.85 2.40 6.90 3.60 d 7343C31 2.55 3.75 2.70 10.20 5.50 2.45 3.35 2.60 9.10 5.00 2.35 2.95 2.50 8.20 4.70 h 7260-20 4.25 2.65 3.20 10.10 7. 20 4.15 2.25 3.30 9.40 6.70 4.05 1.85 3.00 8.10 6.40 e1 7260C38 4.25 2.65 3.20 10.10 7. 20 4.15 2.25 3.30 9.40 6.70 4.05 1.85 3.00 8.10 6.40 r 2012C12 1.05 1.80 1.00 4.80 2.40 0.95 1.45 0.90 3.80 1.90 0.85 1.05 0.80 2.90 1.60 s2 3216C12 1.35 2.15 1.45 6.10 2.80 1.25 1.75 1.35 5.00 2.30 1.15 1.35 1.25 4.10 2.00 t 3258C12 2.35 2.15 1.45 6.10 4.00 2.25 1.75 1.35 5.00 3.50 2.15 1.35 1.25 4.10 3.20 u 6032C15 2.35 2.65 2.60 8.90 4.40 2.25 2.25 2.50 7.80 3.90 2.15 1.85 2.40 6.90 3.60 v 7343C20 2.55 3.75 2.70 10.20 5.50 2.45 3.35 2.60 9.10 5.00 2.35 2.95 2.50 8.20 4.70 x1 7343C43 2.55 3.75 2.70 10.20 5.50 2.45 3.35 2.60 9.10 5.00 2.35 2.95 2.50 8.20 4.70 y1 7343C35 2.55 3.75 2.70 10.20 5.50 2.45 3.35 2.60 9.10 5.00 2.35 2.95 2.50 8.20 4.70 density level a: for low-density product applications. recommended for wave solder applications and provides a wider process window for refow solder processes. density level b: for products with a moderate level of component density. provides a robust solder attachment condition for refow solder processes. density level c: for high component density product applications. before adapting the minimum land pattern variations the user should perform qualifcation testing based on the conditions outlined in ipc standard 7351 (ipcC7351). 1 height of these chips may create problems in wave soldering. 2 land pattern geometry is too small for silkscreen outline. www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 8 8 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum time temperature t smin 25oc to peak t l t s 25 t p t smax t l t p maximum ramp up rate = 3oc/seconds maximum ramp down rate = 6oc/seconds soldering process kemets families of surface mount capacitors are compatible with wave (single or dual), convection, ir, or vapor phase refow techniques. preheating of these components is recommended to avoid extreme thermal stress. kemet's recommended profle conditions for convection and ir refow refect the profle conditions of the ipc/jCstdC020d standard for moisture sensitivity testing. the devices can safely withstand a maximum of three refow passes at these conditions. please note that although the x/7343C43 case size can withstand wave soldering, the tall profle (4.3 mm maximum) dictates care in wave process development. hand soldering should be performed with care due to the diffculty in process control. if performed, care should be taken to avoid contact of the soldering iron to the molded case. the iron should be used to heat the solder pad, applying solder between the pad and the termination, until refow occurs. once refow occurs, the iron should be removed immediately. wiping the edges of a chip and heating the top surface is not recommended. during typical refow operations, a slight darkening of the gold- colored epoxy may be observed. this slight darkening is normal and not harmful to the product. marking permanency is not affected by this change. profle feature snpb assembly pb-free assembly preheat/soak temperature minimum (t smin ) 100c 150c temperature maximum (t smax ) 150c 200c time (t s ) from t smin to t smax ) 60 C 120 seconds 60 C 120 seconds ramp-up rate (t l to t p ) 3c/seconds maximum 3c/seconds maximum liquidous temperature (t l ) 183c 217c time above liquidous (t l ) 60 C 150 seconds 60 C 150 seconds peak temperature (t p ) 220c* 235c** 250c* 260c** time within 5c of maximum peak temperature (t p ) 20 seconds maximum 30 seconds maximum ramp-down rate (t p to t l ) 6c/seconds maximum 6c/seconds maximum time 25c to peak temperature 6 minutes maximum 8 minutes maximum note: all temperatures refer to the center of the package, measured on the package body surface that is facing up during assembly refow. *case size d, e, p, y, and x **case size a, b, c, h, i, k, m, r, s, t, u, v, w, and z construction polymer /ta 2 o 5 /ta silver adhesive carbon silver paint washer tantalum wire weld leadframe (-cathode) leadframe (+anode) www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 9 9 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum capacitor marking storage all ko-cap series are shipped in moisture barrier bags with a desiccant and moisture indicator card. these series are classifed as msl3 (moisture sensitivity level 3). product contained within the moisture barrier bags should be stored in normal working environments with temperatures not to exceed 40c and humidity not in excess of 60% rh. www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 10 10 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum tape & reel packaging information kemets molded tantalum and aluminum chip capacitor families are packaged in 8 and 12 mm plastic tape on 7" and 13" reels in accordance with eia standard 481C1 : embossed carrier taping of surface mount components for automatic handling. this packaging system is compatible with all tape-fed automatic pick-and-place systems. table 3 C packaging quantity case code tape width (mm) 7" reel* 13" reel* kemet eia r 2012-12 8 2,500 10,000 i 3216-10 8 3,000 12,000 s 3216-12 8 2,500 10,000 t 3528-12 8 2,500 10,000 m 3528-15 8 2,000 8,000 u 6032-15 12 1,000 5,000 l 6032-19 12 1,000 5,000 w 7343-15 12 1,000 3,000 z 7343-17 12 1,000 3,000 v 7343-20 12 1,000 3,000 a 3216-18 8 2,000 9,000 b 3528-21 8 2,000 8,000 c 6032-28 12 500 3,000 d 7343-31 12 500 2,500 y 7343-40 12 500 2,000 x 7343-43 12 500 2,000 e/t428p 7260-38 12 500 2,000 h 7260-20 12 500 2,000 * no c-spec required for 7" reel packaging. c-7280 required for 13" reel packaging. top tape thickness 0.10 mm (0.004") maximum thickness 8 mm (0.315") or 12 mm (0.472") 180 mm (7.0") or 330 mm (13.0") www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 11 11 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum figure 1 C embossed (plastic) carrier tape dimensions po t f w cent er line s of ca vity ao bo user direction of unre elin g cover tape ko b 1 is for tape feeder reference only, including dra ft concentric abou t b o . t 2 ?d 1 ?do b 1 s 1 t 1 e 1 e 2 p 1 p 2 embossment for c avity size, see note 1 table 4 [10 pitches cumulative tolerance on tape 0.2 mm] table 4 C embossed (plastic) carrier tape dimensions metric will govern constant dimensions millimeters (inches) tape size d 0 d 1 minimum note 1 e 1 p 0 p 2 r reference note 2 s 1 minimum note 3 t maximum t 1 maximum 8 mm 1.5 +0.10/-0.0 (0.059 +0.004/-0.0) 1.0 (0.039) 1.75 0.10 (0.069 0.004) 4.0 0.10 (0.157 0.004) 2.0 0.05 (0.079 0.002) 25.0 (0.984) 0.600 (0.024) 0.600 (0.024) 0.100 (0.004) 12 mm 1.5 (0.059) 30 (1.181) 16 mm variable dimensions millimeters (inches) tape size pitch b 1 maximum note 4 e 2 minimum f p 1 t 2 maximum w maximum a 0 ,b 0 & k 0 8 mm single (4 mm) 4.35 (0.171) 6.25 (0.246) 3.5 0.05 (0.138 0.002) 4.0 0.10 (0.157 0.004) 2.5 (0.098) 8.3 (0.327) note 5 12 mm single (4 mm) & double (8 mm) 8.2 (0.323) 10.25 (0.404) 5.5 0.05 (0.217 0.002) 8.0 0.10 (0.315 0.004) 4.6 (0.181) 12.3 (0.484) 16 mm triple (12 mm) 12.1 (0.476) 14.25 (0.561) 5.5 0.05 (0.217 0.002) 8.0 0.10 (0.315 0.004) 4.6 (0.181) 16.3 (0.642) 1. the embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. dimensions of embossment location and hole location shall be applied independent of each other. 2. the tape, with or without components, shall pass around r without damage (see figure 5). 3. if s 1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see eia standard 481Cd, paragraph 4.3, section b). 4. b 1 dimension is a reference dimension for tape feeder clearance only. 5. the cavity def ned by a 0 , b 0 and k 0 shall surround the component with suff cient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20 maximum for 8 and 12 mm tapes and 10 maximum for 16 mm tapes (see figure 2). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see figure 3). (e) see addendum in eia standard 481Cd for standards relating to more precise taping requirements. www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 12 12 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum packaging information performance notes 1. cover tape break force: 1.0 kg minimum. 2. cover tape peel strength: the total peel strength of the cover tape from the carrier tape shall be: tape width peel strength 8 mm 0.1 to 1.0 newton (10 to 100 gf) 12 and 16 mm 0.1 to 1.3 newton (10 to 130 gf) the direction of the pull shall be opposite the direction of the carrier tape travel. the pull angle of the carrier tape shall be 165 to 180 from the plane of the carrier tape. during peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 10 mm/minute. 3. labeling: bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. refer to eia standards 556 and 624 . figure 2 C maximum component rotation ao bo t s max imum c ompon en t rota ti on t op view maxi mum co mponent rotat ion s id e view tape m ax imum width (mm) r otat io n ( t ) 8,12 20 16 ? 200 10 tap e m aximum wid th ( mm) ro tat ion ( s ) 8,12 20 16 ? 56 10 72 ? 200 5 typical pocke t cente r line typical com po nent centerline figure 3 C maximum lateral movement 0.5 mm maxi mum 0.5 mm maxi mum 8 mm & 1 2 mm tape 1.0 mm maxi mum 1.0 mm maxi mum 1 6 mm tape figure 4 C bending radius r r b en ding radius e mbo ssed carrier p unc hed ca rrier www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 13 13 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum figure 5 C reel dimensions a d (see note) full radi us, see note b (see note) access hole at slot location (? 40 mm minimum) if present, tape slot in core for t ap e start: 2.5 mm minimum width x 10.0 mm minimum depth w 3 (includes flange distortion at outer edge) w 2 (m ea sured at hu b) w 1 (m ea sured at hu b) c (arbor hole diameter) note: drive spokes optional; if used, dimensions b and d shall apply. n table 5 C reel dimensions metric will govern constant dimensions millimeters (inches) tape size a b minimum c d minimum 8 mm 178 0.20 (7.008 0.008) or 330 0.20 (13.000 0.008) 1.5 (0.059) 13.0 +0.5/-0.2 (0.521 +0.02/-0.008) 20.2 (0.795) 12 mm 16 mm variable dimensions millimeters (inches) tape size n minimum w 1 w 2 maximum w 3 8 mm 50 (1.969) 8.4 +1.5/-0.0 (0.331 +0.059/-0.0) 14.4 (0.567) shall accommodate tape width without interference 12 mm 12.4 +2.0/-0.0 (0.488 +0.078/-0.0) 18.4 (0.724) 16 mm 16.4 +2.0/-0.0 (0.646 +0.078/-0.0) 22.4 (0.882) www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 14 14 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum figure 6 C tape leader & trailer dimensions trailer 16 0 mm minimum carrier t ape end start rou nd sp rock et holes el ongated spro ck et holes ( 32 mm tape and wi de r) t op co ve r t ape top c ove r t ape p unche d carrier 8 mm & 12 mm only e mboss ed carrier components 100 mm minimum leader 400 mm minimum figure 7 C maximum camber carrier tape round sprocket holes 1 mm ma ximum , either direction straight edge 250 mm elongated sprocket holes (32 mm & wider ta pe s) www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 15 15 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum kemet corporation world headquarters 2835 kemet way simpsonville, sc 29681 mailing address: p.o. box 5928 greenville, sc 29606 www.kemet.com tel: 864-963-6300 fax: 864-963-6521 corporate off ces fort lauderdale, fl tel: 954-766-2800 north america southeast lake mary, fl tel: 407-855-8886 northeast wilmington, ma tel: 978-658-1663 west chester, pa tel: 610-692-4642 central novi, mi tel: 248-994-1030 carmel, in tel: 317-706-6742 west milpitas, ca tel: 408-433-9950 mexico zapopan, jalisco tel: 52-33-3123-2141 europe southern europe geneva, switzerland tel: 41-22-715-0100 paris, france tel: 33-1-4646-1009 sasso marconi, italy tel: 39 - 051-939111 milan, italy tel: 39-02-57518176 rome, italy tel: 39-06-23231718 madrid, spain tel: 34-91-804-4303 central europe landsberg, germany tel: 49-8191-3350800 dortmund, germany tel: 49-2307-3619672 kwidzyn, poland tel: 48-55-279-7025 northern europe bishops stortford, united kingdom tel: 44-1279-757201 weymouth, united kingdom tel: 44-1305-830747 coatbridge, scotland tel: 44-1236-434455 f?rjestaden, sweden tel: 46-485-563934 espoo, finland tel: 358-9-5406-5000 asia northeast asia hong kong tel: 852-2305-1168 shenzhen, china tel: 86-755-2518-1306 beijing, china tel: 86-10-5829-1711 shanghai, china tel: 86-21-6447-0707 taipei, taiwan tel: 886-2-27528585 southeast asia singapore tel: 65-6586-1900 penang, malaysia tel: 60-4-6430200 bangalore, india tel: 91-806-53-76817 note: kemet reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. kemet does not assume any responsibility for infringement that might result from the use of kemet capacitors in potential circuit designs. kemet is a registered trademark of kemet electronics corporation. www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 16 16 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum other kemet resources tools resource location conf gure a part: capedge http://capacitoredge.kemet.com spice & fit software http://www.kemet.com/spice search our faqs: knowledgeedge http://www.kemet.com/keask product information resource location products http://www.kemet.com/products technical resources (including soldering techniques) http://www.kemet.com/technicalpapers rohs statement http://www.kemet.com/rohs quality documents http://www.kemet.com/qualitydocuments product request resource location sample request http://www.kemet.com/sample engineering kit request http://www.kemet.com/kits contact resource location website www.kemet.com contact us http://www.kemet.com/contact investor relations http://www.kemet.com/ir call us 1-877-mykemet twitter http://twitter.com/kemetcapacitors disclaimer all product specif cations, statements, information and data (collectively, the information) are subject to change without notice. all information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute C and we specif cally disclaim C any warranty concerning suitability for a specif c customer application or use. this information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. any technical advice inferred from this information or otherwise provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained. although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. www.datasheet.net/ datasheet pdf - http://www..co.kr/
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com t 2060_t545 ? 8/2/2012 17 17 kemet organic capacitor (ko-cap) t545 series high energy polymer tantalum www.datasheet.net/ datasheet pdf - http://www..co.kr/

▲Up To Search▲

Price & Availability of T545Y337M010ATE035

	To Download T545Y337M010ATE035 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .